Machine shop owner Chuck Willard used his Land & Sea engine dyno to break in the newly rebuilt 455 H.O. and measure its output, which after a lengthy tuning session peaked at 433 hp at 4,800 rpm and 517 lb-ft at 3,500 rpm. Quite pleased with the results, we were extremely excited to find the rebuild added what seemed to be about 100 additional hp and 75 lb-ft of torque!

Once reinstalled in the vehicle, the 455 H.O. performed much better at every speed and operating condition. The improvement in full-throttle performance at mid- and high-rpm was dramatic. Measuring just how much we gained was just a chassis dyno session away, and with our 455 H.O. tuned for optimal performance on the engine dyno, we were confident we’d see the maximum result within a handful of pulls. We scheduled an appointment with H.S. Automotive & Dyno, strapped the Trans Am to the roller drum, and let the 455 H.O. sing out the tailpipes.

Unlike an engine dyno, which only takes the water-brake resistance into account when tuning, and uses minimal accessories and very little exhaust backpressure, a chassis dyno allows the operator to tune a vehicle for conditions very similar to what the engine will see on the road in normal operating conditions. After leaning out the carburetor slightly, the 455 H.O. peaked at 303 rwhp at 4,900 rpm and 369 rwtq at 3,700 rpm. Compared to our initial dyno session, that’s an increase of more than 40 rwhp and 40 rwtq—a gain of about 14 percent!

DYNO RESULTS
Before After Difference
RPM RWHP RWTQ RWHP RWTQ RWHP RWTQ
2,600 144 288 170 323 26 35
2,700 154 297 181 340 27 43
2,800 162 302 189 345 27 43
2,900 170 305 199 349 29 44
3,000 178 310 207 354 29 44
3,100 188 316 217 357 29 41
3,200 195 318 225 360 30 42
3,300 203 321 233 363 30 42
3,400 210 322 245 364 35 42
3,500 216 320 249 365 33 45
3,600 217 319 256 366 39 47
3,700 229 325 263 369 34 44
3,800 238 327 269 367 31 40
3,900 242 325 274 364 32 39
4,000 248 324 277 362 29 38
4,100 253 322 280 358 27 36
4,200 256 318 285 350 29 32
4,300 259 316 288 349 29 33
4,400 259 308 292 344 33 36
4,500 260 302 293 337 33 35
4,600 262 297 294 330 32 33
4,700 261 290 297 329 36 39
4,800 260 283 299 324 39 41
4,900 261 279 303 317 42 38
5,000 262 274 301 308 39 34
5,100 261 268 294 304 33 36
5,200 259 261 295 295 36 34
5,300 253 256 288 288 35 32
5,400 246 250 284 279 38 29
5,500 238 243 276 272 38 29
AVG 228 300 261 338 33 38

When comparing the numbers our 455 H.O. generated on the engine dyno to those recorded at the rear tires on the chassis dyno, our particular Firebird sees an equipment loss of about 30 percent. A quick call to Mustang Dyno’s technical department revealed that our calculations were correct, and 30 percent is indeed a reasonable number when considering our Trans Am contains a fully contented accessory-drive system, a Turbo 400 automatic transmission, and an exhaust system consisting of 2.5-inch–diameter tubing and a stock-type transverse muffler.

The addition of a more efficient exhaust system and/or removing drivebelts or eliminating such equipment will likely reduce that number. But we’re confident this particular Firebird (and any others we own that are similarly contented) will show about 30 percent less than what we might otherwise see on an engine dyno. This will help us accurately predict just how much power future modifications may give us in crankshaft values.

With the 455 H.O. rebuild complete and the fresh engine tested in two different forms, we can now appreciate the newfound power by driving the Trans Am as often as possible. Not only can we feel more power from the go-pedal under our right foot, we have proven in our own minds that we have 433 hp and 517 lb-ft available at the tip of our toe, and that’s nearly 15 percent better than it was before!

SOURCE
Willard Auto Machine
7620 N 96th St
Omaha
NE  68122
402-573-8984
http://www.wampowered.com/
H.S. Automotive & Dyno
Omaha
NE
402-895-8863
https://www.facebook.com/HsAutom
otiveAndDyno