Some hobbyists have no qualms pushing the envelope when attempting to maximize the performance of a combination, and that can include any component of the drivetrain. Without careful attention to detail, however, one can create a temperamental vehicle that's unhappy cruising at any speed and/or an engine unwilling to run on pump gas. Few can then blame such owners who are reluctant to venture far from home, fearing major malfunction or the inability to find quality fuel on the open road.
There are others, however, who wish to combine strong performance and a low-maintenance design. Though it may ultimately cost a few horsepower, the result is usually an engine that can be driven any distance or speed while happily operating on marginal-quality fuel. If this sounds desirable, then a powerplant like that featured here is for you. Follow along as we document the assembly of a 474ci engine that produces high horsepower on ordinary pump gas.
Buildup Basics
Dave Hall of Restore A Musclecar in Lincoln, Nebraska, explains to HPP his desire to boost the performance of his company's flagship show car. "Our '77 Trans Am gets driven long distances on events like the Bandit Run, and our technician, Gary Otto, rebuilt its T/A 6.6 engine during the total restoration a few years back. He mildly ported the original 6X-4 cylinder heads and added a Performer RPM intake manifold and Demon carburetor. The roller camshaft and rocker arms came from Butler Performance."
Of the combination, Dave states, "It runs pretty well, especially with headers, a five-speed manual transmission, and deep rear gears, but we kept the engine build somewhat mild because of its intended usage." The company went all out with the suspension and brakes, and the T/A's looks and sound seemed to draw attention, but it became quickly evident that its straight line performance prowess didn't match its heavily modified, corner-carving image.
Hall sought the expertise of Butler Performance in Leoma, Tennessee, and explained his goals to David Butler. "I wanted something that produced around 550-600 hp using a stock Pontiac block," he says. "I also told him that the combination needed to be suitable for in-town cruising or cross-country trips, and that meant that power brakes and air conditioning were a must.
"He laid out a 474ci combination that would suit our needs using a spare 455 block I had. He then provided us with virtually everything necessary to assemble the long-block, including a complete rotating assembly with forged components."
Starting with a two-bolt '71 455ci block and working with the measurements that Butler supplied, Hall had machinist Jon Wischmann prepare the block to accommodate the waiting internals. After complete machining, technician Gary Otto assembled the short-block with relative ease. "We checked all the clearances along the way, and everything was within the stated specifications," he adds. Once the 474ci was fully assembled, Hall and his crew gathered at Spanel Engines in Lincoln for dyno tuning.
A series of eight pulls were made on the Superflow SF-901 dyno, and most consisted of unique timing and/or carburetor settings. All numbers were corrected to standard conditions, and at the end of the session, the mill had peaked at an astounding 578 hp and 588 lb-ft of torque using 92-octane fuel-well within Hall's request of Butler.
Analyzing The Results
After digesting the results, David Butler comments, "The numbers look very good. We've seen 600 hp and 600 lb-ft of torque, sometimes slightly more from this combination with compression toward 11.5:1, which should operate suitably on 92- to 93-octane fuel with the aluminum heads. This wasn't a 'dyno' combo, however, which might typically include borderline compression, a huge camshaft, and a large carburetor. Instead, we took a conservative approach based on the vehicle's intended use."

Dave Hall of Restore A Muscle...

Dave Hall of Restore A Muscle Car in Lincoln, Nebraska, was seeking to significantly improve his Trans Am's performance without compromising its reliability or operational qualities. Butler Performance in Leoma, Tennessee, had the answer, providing the matched components necessary for Dave's 455ci block to produce over 575 hp on low-octane pump gas.

Machinist Jon Wischmann prepares...

Machinist Jon Wischmann prepares Hall's two-bolt '71 No. 485428 455ci block for the rotating assembly kit from Butler Performance. He bores the block 0.060 inch to a total 4.21, machines the deck surface to achieve a true zero deck, adds four-bolt steel main caps, and installs a fresh set of camshaft bearings.

With machine work complete,...

With machine work complete, technician Gary Otto thoroughly washes the block with soap and water...

...and threads a tap into...

...and threads a tap into each bolt hole to remove the debris that's accumulated over the years. Once finished, the block's internals are masked off and the exterior receives a fresh coat of gloss black enamel.

Working within Hall's parameters,...

Working within Hall's parameters, Butler Performance sent a custom-ground hydraulic-roller camshaft and lifter set from Comp Cams. Duration at 0.050-inch lobe lift is 242/248 degrees and lobe separation angle is at 110 degrees. Gross valve lift, when combined with 1.5:1-ratio rocker arms, is 0.540/0.562 inch.

With the block back from paint,...

With the block back from paint, Otto installs the camshaft first. He feels this method gives him the control needed to prevent damaging the soft cam bearings. Fitting the rear main seal from BOP Engineering is next.

The rotating assembly kit...

The rotating assembly kit that Butler Performance recommended for the build includes this forged-steel crankshaft, featuring a 4.25-inch stroke and 3.25-inch main- and 2.2-inch rod-journal diameters. Total displacement yields 474 ci when combined with the 0.060-over 455 block. After threading the ARP main studs into the block and setting the upper half of each Federal Mogul main bearing in place, Otto installs the crankshaft, lower bearings, Pro-Gram main caps, and remaining ARP hardware. The nuts of the four forward caps are incrementally torqued to 95 lb-ft using the supplied moly-lube, while the rear cap's nuts are torqued to 135 lb-ft. Crank endplay is checked and is well within the acceptable range.

Also included in the rotating...

Also included in the rotating assembly kit from Butler Performance are forged-steel Eagle connecting rods in 6.8-inch length, Butler-spec forged-aluminum Ross pistons, Total Seal piston rings, and Ferrea wristpins.

The piston rings are file...

The piston rings are file fit to a gap of 0.018 inch. Otto then installs the rings and full-floating wristpins, removes the rod caps, and lays each assembly in corresponding order. He thoroughly coats each piston with 30-weight oil, compresses the ring pack, and taps each one into its respective bore. Extreme caution is used to ensure that the connecting rod doesn't damage the crankshaft journal during installation.